登录 | 注册
产品中心
首页 > 产品中心 > Aluminum and aluminum alloy casting series auxiliaries > Refining flux

Refining flux

1.Principle:

   By use of powder spraying machine,spray powder Refining flux into aluminum melt bath with high purity nitrogen.Under the combined effect of dispersed tiny nitrogen bubble and flux, it will eliminate the entrapped slag and hydrogen in aluminum liquid.

2.Main features:

1) High efficiency,100% efficient composition.

2) Strong purifying capacity up to domestic advanced level.

3) Less pollution, small consumption and low cost.

3.Use method:

   Add refining flux of required amount into refining tank and cover it properly, turn on the switch of refining tank and connect nitrogen gas. When refining flux is spraying out of refining iron tube, insert it into the furnace and move all around inside evenly for 2 or 3 times.When powder inside the tank is sprayed completely, first draw out the refining tube out of aluminum liquid, and then swith off nitrogen gas.

4.Technical parameters:

1) Refining temperature:700ºC~740ºC

2) Refining time:8~15minutes (6~20ton furnace)

3) Nitrogen pressure:1.2~1.8kg/mm2

4) Use level 1~3kg for one ton aluminum.

 

 

5.Precautions:

1) The refining time shall be extended along with increase of aluminum melting volume.

2) The powder feeding rate can be controlled by adjusting switch on the bottom of refining tank.Generally, there shall be powder spraying out within the range of refining time.

3) The end of refining tube shall be inserted into the furnace by 2/3 of the aluminum liquid depth.The tube shall be moved to left and right side.The furnace wall and bottom shall not be touched to prevent from clogging of tube.

4) The turbulence height of aluminum liquid shall be controlled by nitrogen pressure.Under the premise of preventing from clogging of tube, the higher turbulence is acceptable.It is better to control below 15cm.

6.Packaging and storage:

   It is 2kg for each package and 20kg for each box, which shall be stored in a dry and ventilated place. The storage period is one year if plastic bag are not damaged. It can be further used when it is ground into powder and dried under the temperature of 100ºC.


<span style="font-size: 16px;"><a href='https://cn.huaaochemtech.com/tag/refining-flux' target='_blank' class='key-tag'><font><strong>Refining flux</strong></font></a> for Aluminum Melt Treatment | Huaao</span>

At Jianli Huaao Technology Co., Ltd., we help aluminum processors select refining flux around the condition of the melt and the requirements of the next production step. We start with the alloy, identify the treatment target, and discuss a product specification that fits your equipment and working practice.

Our focus is practical: process compatibility, consistent batch requirements, and treatment results your team can check. Whether you cast automotive parts, machinery components, or electrical housings, we want the material choice to connect with an actual production need.

We use refining flux here for aluminum melt-treatment products selected for defined cleaning or impurity-control functions. The exact role depends on the formulation. We confirm that role, the application conditions, and the supplied technical indicators before an order becomes a routine production item.

We Start with the Melt Condition You Need

We usually begin a technical discussion with one question: what needs to change in the melt? You may be seeing nonmetallic particles in a sample, investigating an unwanted element, or reviewing a treatment that varies between shifts. Those concerns call for different checks, even when purchasing uses the same product name.

We explain inclusions as small pieces of unwanted solid material within the metal. Oxide films are one example. They can be difficult to judge from the appearance of the furnace surface, which is why we ask how your plant measures cleanliness and where the samples are taken.

We discuss dissolved elements separately. Sodium, calcium, or another element may need control in a particular alloy, while other elements must remain within the finished alloy specification. We review the actual composition and target limits before selecting an Aluminum Refining Flux.

We also ask about hydrogen. If the main concern is gas-related porosity, your degassing process and its measurements belong in the conversation. A product selected for inclusion cleaning cannot be assumed to solve every source of porosity.

For a useful inquiry, we need more than “better purification.” We might define the target as a change in a specified inclusion test, an agreed final concentration of a named element, or stable treatment results across representative heats. A defined target gives production and purchasing the same basis for review.

We look at the next step too. A melt moving directly to casting has a different process history from one held for an extended period and transferred several times. We want the evaluation to reflect the route the metal actually follows.

Our role is to connect the product with that route. We discuss what the selected grade is intended to do, what equipment it needs, and which checks show whether it has done the job. That is the starting point for a refining flux specification your team can use.

How We Explain Refining Flux Inside the Bath

We describe conventional salt-based melt treatment as controlled contact between the flux and the material being targeted. The formulation needs to suit the temperature and alloy, and the application needs to bring it into useful contact with the melt.

For inclusion cleaning, we consider how the treatment interacts with oxide and other nonmetallic particles. Suitable fluxes can help collect those particles into a phase that can be separated from the metal. We pay attention to distribution because material left in one small area cannot treat the entire bath equally.

For element removal, we consider a different requirement: a suitable chemical reaction with the named impurity. Pyrotek's refining-agent literature describes products designed to target unwanted elements such as sodium, lithium, and calcium. We use that as a general example of selective treatment, not as a claim that every refining flux removes those elements.

We also explain why product form matters. A powder blend, a granular product, and a fused flux describe different physical or manufacturing characteristics. Fused fluxes are made by combining salts through melting. Granular describes particle form, so a fused product may also be supplied as granules.

We review the selected form against the addition equipment. A material suitable for manual treatment may have different requirements from one metered through an injection system. Flow behavior, particle size, and contact conditions all become part of the application discussion.

We keep three treatment functions clear. Cleaning concerns unwanted material within the melt. Drossing helps separate metal from the surface residue. Covering provides surface protection. A formulation may support more than one function, but we confirm which functions are included in the selected grade.

We also distinguish refining flux from grain refining flux. The first term on this page concerns melt cleaning and defined impurity control. Grain refinement concerns the crystal structure that forms as aluminum solidifies. We clarify that distinction when reviewing translated specifications or older purchase descriptions.

Our technical approach is straightforward: the chemistry, the contact method, and the treatment target need to match. We then verify the result using the measurement agreed for your production requirement.

How We Match Alloy Chemistry, Temperature, and Addition Method

We check what must stay in the alloy

We ask for the alloy designation and a recent analysis. This helps us identify both unwanted elements and elements that are intentionally present. If your material contains magnesium, for example, we need to understand its specified range before discussing a treatment that could affect it.

We also ask about sodium restrictions, modification practice, and any downstream sensitivity to residual salts or unwanted elements. These details help turn “refining flux for aluminum alloys” into a specific selection discussion.

We check the real operating window

We review the temperature where treatment takes place, including the variation during a normal heat. A published flux melting point and a published application temperature are different pieces of information. We need the actual grade's working instructions to judge suitability.

The external reference data below show how even products within a refining range can have different operating windows and addition quantities. We include them for comparison; they do not establish Huaao product specifications.

Table 1. Published application data for selected ADtech refining flux grades
External reference gradePublished refining temperaturePublished addition per tonneCalculated equivalent relative to 1,000 kg of metal
3RF700–740°C1.5–2.5 kg0.15–0.25%
420RF710–730°C1.5–2.5 kg0.15–0.25%
560RF720–740°C1.5–2.0 kg0.15–0.20%

Source: ADtech,Refining Flux, official product comparison. We calculated the percentages using a 1,000 kg metal basis. These are manufacturer-published reference values, not independent comparative test results, Huaao operating instructions, or claims of product equivalence.

We read those figures together with each product's intended function. A smaller published addition does not automatically mean better treatment or a lower cost for your process. The alloy, initial condition, and required result still decide whether the comparison is useful.

We check the way the flux reaches the melt

We discuss manual addition, mechanical mixing, and injection according to your equipment. For an injection system, we review the feeder, delivery path, and approved carrier-gas arrangement with your team. The selected grade needs to fit that system.

We then confirm the actual supply specification and application information for evaluation. This keeps the product choice connected to the furnace and prevents a reference table from becoming an accidental production instruction.

Where We Discuss Aluminum Refining Flux Applications

Automotive parts and structural castings

We discuss aluminum melt treatment for automotive components with the part requirements in view. A housing, a bracket, and a pressure-containing casting may have different acceptance checks. We identify the relevant melt-quality target before deciding how the trial should be evaluated.

We keep the casting route visible in that discussion. Sand casting, gravity casting, low-pressure casting, and high-pressure die casting involve different holding and transfer practices. A successful result in one route is useful information, but it needs review before being carried into another.

Machinery manufacturing

For machinery castings, we ask about internal returns, alloy changes, and machining-related quality concerns. If a defect appears after machining, we want a consistent inspection method and a clear record of where the affected material came from.

We also discuss how approved products are identified on the shop floor. A foundry processing several alloy families may need separate treatment instructions. Clear identification helps keep a suitable flux from being used outside its approved application.

Electrical and electronic products

For electrical housings and electronic equipment castings, we review composition limits, cleanliness targets, and subsequent finishing. If conductivity or another electrical property is controlled, we include it in the approval plan. The industry name alone cannot establish the right chemistry.

Recycling and remelting

We discuss refining flux for aluminum recycling according to the feedstock. Clean returns, mixed scrap, and fine material create different treatment conditions. We ask about charge preparation, alloy sorting, and furnace practice so that the flux addresses a defined part of the process.

We also separate chemical treatment from charge correction. If the incoming metal is outside the required composition, we review what the selected treatment can reasonably control and what needs a different production decision.

Across these applications, we aim for a product selection that matches the actual alloy and operating route. That makes the trial relevant to the components you need to deliver.

How We Prepare Treatment for Your Production Line

We prefer to agree the application plan before the first trial heat. It gives operators a clear procedure and gives your quality team a record it can interpret. The selected grade's technical information and your approved plant procedures determine the working conditions.

We establish the starting condition

We record alloy chemistry, charge mix, melt mass, temperature, and the existing treatment sequence. We also agree the baseline sample location and timing. An analysis taken before alloy adjustment should not be compared casually with one taken after several additional production steps.

We include representative heats. A trial based only on unusually clean charge material can miss the variation your plant sees every week. We want to understand the conditions in which routine treatment will actually operate.

We define the addition and contact step

We agree the material identification, weighed quantity, addition point, and intended contact method. Where the product is fed automatically, we discuss how your team checks the delivered quantity. A feeder setting is useful only when its output is understood.

We keep treatment time and temperature within the agreed conditions. We also record the mixing or injection settings that your equipment procedure requires. This makes it easier to compare heats and investigate a result that moves outside the expected range.

We include residue removal and transfer

We review how treatment residues are separated and how the metal reaches the next operation. Refining is part of a route that may also include skimming, degassing, filtration, holding, and pouring. We want the benefit of treatment to survive those later steps.

We also agree where the final sample is taken. Sampling immediately after treatment and sampling at the casting point answer different questions. Both may be useful when you are investigating a change during transfer or holding.

We keep product condition under control

We use the selected formulation's SDS and packaging instructions to define storage and handling requirements. Salt-based materials can have different moisture sensitivities, so we confirm the guidance for the actual supply. Your plant procedures control application tools, ventilation, and operator protection.

We record any damaged packaging or unusual material condition before use. If a product has absorbed moisture, we do not improvise a drying procedure. We resolve its suitability through the applicable product information and your approved process.

We turn an accepted trial into a repeatable instruction

We help capture the approved grade, quantity basis, operating range, inspection points, and acceptance requirements. That gives the next shift and the next delivery the same starting conditions. Routine production becomes easier to review when those details are written clearly.

What We Measure Before Calling a Trial Successful

We judge a refining flux trial against the target agreed at the beginning. Inclusion cleaning needs an inclusion-related assessment. Element removal needs an appropriate chemical analysis. Hydrogen control needs its own measurement. We use the test that answers the actual question.

We make small concentrations easier to understand

We often discuss trace elements using parts per million, or ppm, on a mass basis. One ppm by mass is equivalent to one milligram per kilogram. The table below converts example concentrations into the mass of an element in two different melt quantities.

Table 2. Calculated element mass at selected trace concentrations
Illustrative concentration on a mass basisElement mass in 1,000 kg of meltElement mass in 5,000 kg of melt
1 ppm / 1 mg/kg1 g5 g
5 ppm / 5 mg/kg5 g25 g
10 ppm / 10 mg/kg10 g50 g

Source: our mass calculations using the relative-value meaning of ppm described in NIST Special Publication 330, Section 5. Element mass in grams = concentration in mg/kg × melt mass in kg ÷ 1,000. These are unit conversions, not measured impurity levels, alloy limits, removal targets, or Huaao performance results.

We use this example to explain why sampling and analysis matter. A concentration that represents only a few grams in a large bath still needs a suitable test method. We also need to know whether the laboratory can reliably measure the level being discussed.

We keep the measurements comparable

We agree the sampling tools, location, timing, preparation, and reporting method with your quality team. If a result is close to a reporting limit, we review that limit before treating a small numerical difference as proof of improvement.

We keep production records beside the results. A change in returns, alloy additions, holding duration, or transfer can affect the comparison. The record helps us explain variation instead of assigning every change to the flux.

We calculate the full treatment cost

We calculate direct flux cost from delivered price and actual consumption per tonne treated. We then review documented effects on quality, metal loss, handling, and treatment time where those measurements are available.

We also include the acceptance requirement. A lower treatment cost has little practical value if the melt misses the required condition. We look for a repeatable result at an acceptable total cost and keep any claimed improvement tied to the trial evidence.

Why Work with Huaao on Selection and Supply?

We are Jianli Huaao Technology Co., Ltd., a technology-oriented enterprise engaged in chemical additive research, production, sales, and technical consulting. We have served the aluminum profile surface treatment industry for more than two decades.

We are located in the Huazhong Ecological Aluminum Demonstration Industrial Park in Jianli, Hubei, China. We serve as a standing council member of the China Non-Ferrous Metals Processing Industry Association. Our company supports its work with production facilities, precision testing instruments, and a quality assurance system.

Our wider additive experience includes aluminum pretreatment, polishing, etching, electrolytic coloring, sealing, degreasing, and chromium-free passivation. We bring a process-focused approach to customer discussions while confirming the specific requirements of each casting additive.

For refining flux, we organize the selection around the alloy, application method, and required result. We focus on process compatibility and batch consistency, with the supplied technical indicators agreed for the selected product.

We confirm the specification and documents

We deliver according to the technical indicators, quantity, and packaging standards agreed in the contract. We can provide COA and SDS documents as required. If your receiving inspection needs a particular analysis or test method, include it in the inquiry so we can confirm the scope.

We keep batch documentation connected with application approval. A COA reports the agreed batch characteristics. Your trial establishes performance under your conditions. Together, they support a clearer decision on repeat supply.

We agree packaging and delivery requirements

We discuss suitable bag or drum packaging according to the product and order. Pack size, labeling, and handling needs can be confirmed for the actual supply. Production and preparation time depend on product type, stock availability, and order quantity.

We select transport according to cargo properties and destination. Sea freight, road transport, and eligible air freight can be considered. Where dangerous-goods requirements apply, the packaging and shipment must meet the relevant rules.

We make the quotation specific

We can discuss T/T or letter-of-credit payment terms. To request a refining flux quotation, send your alloy grade, furnace type, temperature range, treatment purpose, expected quantity, and destination. A current specification or recent analysis helps us address the actual requirement.

We use that information to confirm a concrete supply proposal, including the product description, document requirements, packaging, and delivery schedule.

Questions We Address About Refining Flux

What does refining flux do in aluminum processing?

We select it for defined melt-cleaning or impurity-control tasks. Depending on the formulation and method, that may involve inclusion removal or control of named unwanted elements. We confirm the selected product's functions before agreeing its application.

Is refining flux the same as grain refining flux?

We distinguish the terms. The product category on this page concerns melt treatment. Grain refining products are selected to influence the aluminum grain structure during solidification. We check the intended function when reviewing an inquiry or translated specification.

Will it remove every unwanted element?

We assess removal requirements element by element. A formulation designed for one impurity cannot be assumed to control all others. We review the starting analysis, target limit, and available treatment evidence before recommending a product.

Can it replace degassing or filtration?

We review the complete treatment route before changing those steps. Some refining agents support combined processes, but we retain the measurements needed for hydrogen and inclusions. We confirm any proposed change through a controlled evaluation.

How much refining flux should we add?

We establish the quantity from the selected grade's instructions, initial melt condition, application equipment, and target result. Table 1 contains external reference values only. We agree the actual addition basis and operating conditions for your trial.

Is a granular product always better than powder?

We compare the actual products and application methods. Particle form alone does not establish chemistry, suitability, or treatment cost. We review handling, feeding, distribution, and measured performance before approving a substitution.

Can you supply sodium-free or fluoride-free refining flux?

We can discuss those requirements and confirm availability for the order. Any composition limit or special declaration needs a clear definition and product-specific support. We include confirmed requirements in the agreed specification.

What documents can accompany the order?

We can provide COA and SDS documentation as required. Please tell us about any additional receiving or approval requirements during the inquiry, so we can confirm the available scope before the order is finalized.

How do we begin product selection?

We can start with your alloy analysis, furnace information, current treatment sequence, and quality concern. Add the expected order volume, destination, and documentation needs so we can address application and supply together.

Discuss your aluminum melt-treatment requirements with Huaao. We will help clarify the refining flux specification, evaluation conditions, and supply terms for your production line.

在线留言

请填写有效的邮箱地址
验证码 不能为空

相关产品

暂无搜索结果!
chat

×

本网站使用 cookie 来确保您在我们的网站上获得最佳体验。

接受 拒绝