登录 | 注册
产品中心
首页 > 产品中心 > Aluminum and aluminum alloy Surface handle series > Low temperature polishing agent

Low temperature polishing agent

1、Product features:

    This product is a kind of acidic pale green transparent liquid and is prepared by inorganic acid, strong oxidant, inhibitor, brightener, dust inhibitor and surface activator. Compared with conventional alkali etching process, it has the following advantages:

1) It has improved the luster of profile surface and is conducive to stable priming and bright luster of colored profiles. It has special brightening and bleaching effect to sandblasted profiles.

2) Adopting appropriate corrosion inhibitors and surface active agent to overcome the solid solution incomplete aluminum (such as refining, quenching air volume is not enough, crystal serious deflection) surface on sand, bright crystal etc malady.

3) With wide process parameter for tank liquid, it has advantages of low cost, less pollution and simple operation.  

2、Composition of tank liquid: HA—10     30-60kg/m3
                             H2O        Margin

3、Technical parameters:  Temperature       Normal temperature

Time             2~8min
4、Consumption:

   The consumption of Low temperature polishing agent for 1 ton profile is 3~5kg.

5、Packing and storage:

   This product is packed with 25kg air-tight plastic barrels. 


A polished aluminum sample can look impressive under one light and uneven under another. We develop Aluminum surface treatment additives with the final appearance in mind, including the condition after anodizing or another approved finishing step. Our Low temperature polishing agent range is considered for applications seeking controlled chemical polishing at a reduced operating temperature. We select the grade around your alloy, starting surface, equipment, and required finish.

1. We Start With the Finish You Want to Produce

Before discussing bath temperature, we ask what a good part should look like. Do you need a clear reflection, a softer metallic shine, or a brighter version of an existing brushed texture? These are different targets. Treating them as one requirement makes product selection and sample approval harder than they need to be.

A low temperature polishing agent for aluminum is used within a defined chemical finishing process. Depending on the selected formulation and conditions, chemical polishing can change the fine surface texture and improve the way light reflects from it. The required result must be established on the actual material.

We distinguish a polishing additive from a complete working bath. Some products are supplied as ready-to-use solutions; others form part of a bath made up according to specific instructions. The product name alone does not tell an operator how to prepare the solution, replenish it, or control its composition.

We also distinguish lower-temperature chemical polishing from mechanical polishing and electropolishing. Each uses a different way of changing the surface. A chemical polishing additive cannot be selected as a drop-in replacement for abrasive finishing or an electrically driven process without reviewing the complete production route.

The starting surface matters. An extruded profile with visible die lines, a buffed decorative part, and a blasted component do not begin with the same texture. We need to know which features you want to preserve and which defects must be removed before chemical treatment.

For a useful first discussion, we ask for the alloy designation, material condition, photographs, current preparation steps, target sample, and next finishing operation. If several material batches are involved, we want to know that too. A process approved on one selected coupon may not represent the variation reaching your line.

Our goal is a finish your team can recognize, measure, and repeat. We therefore agree the appearance requirement before treating a brighter surface as an improvement. A controlled semi-bright finish can be the right result where a mirror-like surface would conflict with the design.

2. How Chemical Polishing Changes an Aluminum Surface

At a small scale, an aluminum surface contains raised areas and depressions. Chemical brightening can preferentially dissolve raised features, reducing fine surface unevenness. That helps explain the change in reflected light. It also explains why chemical polishing involves controlled material removal rather than simply adding shine to an unchanged surface.

We do not expect a brightening bath to repair deep scratches, dents, or large pits. Those defects may need mechanical preparation or rejection before the part reaches the chemical stage. Extending treatment to chase a deep defect can remove more material elsewhere without producing an acceptable part.

The selected formulation controls how the surface reacts. Bath composition, temperature, contact time, and the condition of the metal all contribute. We evaluate them together because changing one can affect both appearance and the amount of aluminum removed.

Comparing the main polishing routes

ProcessHow the Surface Is ChangedWhat We Evaluate
Mechanical polishingAbrasive contact removes material and changes the surface texture.Scratch removal, access, shape preservation, and preparation consistency.
Chemical brighteningChemical dissolution smooths fine surface features.Alloy response, fine texture, surface removal, and chemical control.
Electrolytic brighteningA controlled electrical process drives surface dissolution in an electrolyte.Electrical conditions, part connection, geometry, and bath compatibility.

Sources: ASM International, Surface Engineering of Aluminum and Aluminum Alloys, ASM Handbook Volume 5, 1994; Mary Oakley and Wayne Chandler, Chemical and Electrolytic Brightening, ASM Handbook Volume 2A, 2018. The evaluation column presents our practical interpretation, not comparative performance test results.

We also review the alloy and its production history. Material supplied under the same broad aluminum description can differ in composition, surface condition, and previous processing. Cast surfaces require particular attention because their response may differ from the wrought profiles used to develop a sample finish.

Part geometry changes exposure. Recesses can retain liquid, upward-facing pockets can trap air, and tightly spaced parts can restrict solution movement. We address these conditions through suitable loading and handling arrangements. Changing the chemistry alone cannot correct an area that the bath does not reach.

A useful chemical polishing agent for aluminum alloys must fit both the metal and the production method. We confirm that fit through representative trials rather than assume that a successful flat sample establishes the result on every component shape.

3. What Lower Processing Temperature Can Change

The phrase Low temperature polishing agent needs a reference point. It does not automatically mean room-temperature use. We ask which existing process is being compared, what finish is required, and which operating window belongs to the selected formulation.

Reducing the required temperature can reduce the theoretical heat needed to raise the same bath from the same starting condition. Actual production energy also depends on tank size, insulation, heat losses, loading, treatment time, and standby operation. We assess energy per accepted production output before discussing a saving.

A lower temperature is useful only when the complete result remains suitable. A process requiring much longer treatment, additional rework, or a different appearance needs a broader comparison. We look at finish quality, output, chemical use, heating, and maintenance together.

Published examples of aluminum chemical polishing conditions

The following figures describe external products and their stated applications. They illustrate the range of published conditions within aluminum chemical polishing. They are not operating instructions for Huaao products or evidence that the listed finishes are equivalent.

Published Reference ProductPublished TemperaturePublished Treatment TimeStated Appearance or Application
OKUNO TOP GREENAL GLOSS 300Usable at 55°CNot stated on the cited product pageSemi-bright appearance; suitable for blast-finished aluminum.
Raiki Pika 190–120°C under the leaflet's general conditions20–180 secondsChemical polishing for applications requiring high reflectivity.

Sources: OKUNO Chemical Industries, TOP GREENAL GLOSS 300 official product information; Raiki, Pika 1 aluminum chemical polishing product leaflet, General Treatment Conditions. Raiki states that conditions vary with the required gloss, material, treatment method, and bath condition. Confirm current instructions before using either reference product.

We use this information to frame the selection question: which formulation delivers the required appearance under conditions your line can maintain? A temperature figure on its own cannot answer that question. The approved Huaao working conditions must come from the selected grade's technical information and application trial.

The advantages we aim to verify

We focus on manageable heating requirements, a consistent surface response, and a process that fits the available equipment. Depending on the application, an appropriate lower-temperature route may help you reconsider tank operation or heating demand. We confirm those benefits against the current process instead of assigning a fixed improvement percentage.

We assess surface removal and appearance together. Less metal removal is not automatically better if the required finish has not developed, while a brighter result is not acceptable if important edges or dimensions have changed. The useful operating window satisfies both requirements.

We do not infer fume-free operation, harmless chemistry, or unrestricted wastewater discharge from the word low-temperature. Handling, ventilation, compatible equipment, and waste treatment follow the actual formulation and safety information. Environmental claims also need to describe the specific grade.

4. Building the Process Around Your Parts

Prepare the surface before polishing

We begin with suitable cleaning. Oil, grease, and polishing compound can interfere with uniform contact between the metal and the polishing bath. If a component arrives with heavy wax residue, we review whether it needs a dedicated de-waxing step rather than asking the polishing bath to handle the full cleaning task.

Mechanical preparation may also be needed where the starting surface contains visible defects. We agree the condition of parts entering chemical treatment so that the trial evaluates the polishing stage fairly. Otherwise, changing preparation from one batch to the next can disguise the cause of an uneven finish.

Control what reaches the bath

We review drainage from the previous stage. Liquid carried in on parts and racks can change bath composition over time. The amount depends on geometry, loading, transfer, and the preceding process. We follow the selected formulation's instructions rather than apply another product's rules for water balance or replenishment.

Rack arrangement should give the working solution suitable access and allow consistent drainage. Long profiles and recessed parts may need different handling arrangements. We document the arrangement used for an accepted trial because the loading method forms part of the process.

Establish a controlled treatment window

We confirm whether the supplied product is a complete bath, a concentrate, or an additive. We then agree preparation and operating instructions for that grade. The trial record should identify temperature, contact time, relevant chemical measurements, and the condition of the incoming parts.

Temperature should represent the working area around the load. A controller setting does not establish that every part sees the same condition. We check how the bath responds when production material enters and whether the measuring arrangement is appropriate to the tank.

We define when treatment time starts and ends. Transfer delays or inconsistent withdrawal can matter when the chemical reaction continues during handling. An operator should be able to follow the approved method without guessing which part of the movement counts as treatment.

Check rinsing and the next finish

After polishing, we follow the approved rinsing and subsequent treatment sequence. Some aluminum processes require a separate desmutting stage to remove residual material. We confirm whether that stage is needed for the selected formulation and alloy rather than assume that every line uses an identical sequence.

For a low temperature polishing agent for anodizing pretreatment, sample approval should include the anodized result. An attractive surface before anodizing may not look the same after the full finish. We evaluate the stage at which the customer will actually judge the product.

We also review tank, heater, pump, seal, and rack compatibility using the formulation's technical and safety information. An existing installation needs that review even if it previously handled a different aluminum polishing chemical.

5. Measuring the Finish and Keeping It Consistent

We approve appearance under agreed viewing conditions. Lighting, viewing angle, surface direction, and the reference sample should remain consistent. A photograph taken under an attractive light can help communication, but it cannot replace an agreed inspection method.

Gloss measurement adds useful numerical information when the instrument and method suit the surface. We record the measurement angle and result together. A gloss value without its geometry is incomplete, and gloss units should not be presented as a percentage of total reflected light.

Comparing published gloss-meter selection guidance

Initial Gloss Reading at 60°General Gloss CategorySuggested Measurement Geometry
Below 10 GULow gloss85°
10–70 GUMedium gloss60°
Above 70 GUHigh gloss20°

Source: Konica Minolta Sensing, How To Select the Right Angle for Gloss Measurement? This is general instrument-selection guidance, not a Huaao product specification or a universal acceptance rule for polished aluminum. We confirm the appropriate method for the actual surface and customer requirement.

Surface shape also affects measurement. A small curved trim part may not provide the flat measuring area an instrument needs. Brushed surfaces require consistent orientation. We agree representative measuring locations and a suitable fixture or sample arrangement before comparing production batches.

Gloss is only part of appearance. We also inspect haze, streaks, pits, and the clarity of reflected detail where relevant. A product may meet an agreed gloss value while still showing a defect that matters to the finished assembly.

Where dimensional change is important, we include a separate material-removal check. That might involve suitable dimensional measurements or a controlled mass-loss method. We select the method around the feature being protected rather than assume gloss establishes how much material was removed.

When the bath or finish changes

If the finish becomes dull or uneven, we examine the incoming parts, cleaning, bath analysis, temperature measurement, loading, and transfer conditions. We compare the affected work with the accepted trial record. Increasing treatment time immediately can hide the original cause and create a new surface-removal problem.

Bath condition should be followed using the selected grade's control method. Drag-out, carry-in, reaction products, and replenishment can alter the working solution. We need both chemical records and surface results to decide whether an adjustment has restored the process.

We review performance across representative production, not just one attractive sample. Repeated batches, difficult geometries, and normal variations in incoming material provide a more useful basis for routine operating instructions.

6. Applications We Evaluate for Aluminum Finishing

Architectural and decorative profiles

For profiles used in doors, windows, interior systems, and decorative framing, we assess appearance over the visible length. We consider extrusion lines, prior finishing, drainage, and the final anodized or otherwise approved surface. Adjacent pieces should be evaluated as an assembly where visual matching matters.

Furniture fittings and decorative hardware

Handles, trim, and other visible fittings often combine flat faces, curved sections, and recesses. We evaluate how a low temperature aluminum polishing process reaches those areas and whether it preserves the intended shape. An approved sample should represent the production geometry rather than a conveniently flat substitute.

Automotive trim and related components

We consider decorative aluminum components where the selected surface treatment fits the customer's specification. Alloy, prior forming, joining, and the final protective finish all affect selection. We do not infer automotive approval or durability from a successful polishing demonstration alone.

Electronic housings and appliance parts

For aluminum covers, panels, and housings, we examine the requested appearance alongside retained liquid, protected areas, and later operations. A grade intended for one decorative surface should not be assumed suitable for a complete assembly containing other materials.

Across these uses, we distinguish decorative brightness from a functional optical requirement. A part designed to reflect light in a controlled way may need additional testing beyond a gloss reading. The chemical polishing stage must be assessed against that actual function.

7. Our Manufacturing Support and Delivery Approach

At Jianli Huaao Technology Co., Ltd., we develop, manufacture, and supply additives for aluminum profile surface treatment. We have worked in this industry for more than two decades, combining research with technical consulting. Our production base is in the Huazhong Ecological Aluminum Demonstration Industrial Park in Jianli, Hubei.

Our facilities, testing instruments, and quality assurance system support product development and production. We also serve as a standing council member of the China Non-Ferrous Metals Processing Industry Association. Product selection still rests on the grade's documentation and its performance in the proposed application.

Our range includes chemical sandblasting agents, polishing products, alkaline etching additives, electrolytic coloring stabilizers, sealing agents, degreasing and de-waxing products, and chromium-free passivation agents. This wider scope helps us discuss how polishing connects with earlier preparation and later treatment.

Defining and controlling the supplied grade

We begin by identifying the application and the product to be evaluated. We distinguish the supplied product's release specification from the customer's working-bath conditions. They are related documents, but they describe different things: what is delivered and how it is used.

Raw-material identification, formulation control, mixing, inspection, and packaging are linked requirements in manufacturing a surface treatment chemical. We discuss the relevant checks for the selected grade and order. A general statement about quality should be supported by identifiable inspection requirements and methods.

The agreed delivery information should identify the product, quantity, batch details, and inspection requirements. Technical instructions and the safety data sheet need to correspond to the supplied material. Where additional documentation is needed, we agree it before confirming the order.

Production schedule and payment terms

We confirm the production schedule according to formulation, order quantity, and required testing. A product awaiting application evaluation needs a different plan from an order with an agreed grade and specification. Confirmed timing belongs in the order agreement.

Payment arrangements may include T/T or L/C, subject to mutual agreement. We confirm the payment stages and document requirements in the contract. We do not apply an assumed deposit rate or payment period to every request.

Packaging, storage, and transportation

We choose packaging according to the product's physical form, chemical compatibility, and safety data sheet. Suitable sealed drums or intermediate bulk containers may be considered for liquids; moisture-resistant packaging may apply to powder products. We confirm the actual package for the selected grade.

Storage instructions must come from the product documentation. The phrase low temperature describes a processing aim and should not be used to infer storage stability, shelf life, or resistance to crystallization. Those properties need their own stated conditions.

Sea freight and road transport can be assessed for suitable orders. Air transport depends on the material classification, approved packaging, carrier requirements, and route. We arrange shipment around the actual chemical information and agreed delivery terms.

8. Low temperature polishing agent FAQ

Does low-temperature polishing mean room-temperature treatment?

No. We use the selected grade's documented working window. Lower temperature is a comparison with a defined alternative, not a universal number. Confirm the required appearance and operating conditions together before deciding whether a formulation fits your line.

Can this product remove deep scratches or dents?

We do not rely on chemical brightening to repair deep surface defects. We assess whether mechanical preparation or another action is needed before chemical treatment. Extending the polishing time can remove additional material without correcting the original defect.

Can every aluminum alloy achieve the same gloss?

No. We evaluate the actual alloy, production condition, and starting surface. The same bath settings should not be assumed to give identical results on profiles, sheets, and castings. Representative material trials establish the appearance that can be accepted.

Can we use the temperature figures in the comparison table?

Those figures belong to the named external reference products. We provide them to explain published differences in process conditions and target appearance. Our Low temperature polishing agent requires its own current technical instructions and an application-specific trial.

Will lower-temperature processing reduce our total cost?

It may, but we assess the whole process before making that claim. Compare measured heating, treatment time, chemical consumption, accepted output, and rework. A reduced bath temperature alone does not establish the overall saving.

Can we approve the product before anodizing?

We can evaluate the polished intermediate surface, but final approval should include the finish the customer will receive. For anodized products, we check the anodized appearance and relevant agreed requirements. Intermediate brightness alone does not establish the final result.

Share your alloy, current preparation method, target finish, and line conditions with us so we can discuss a suitable Low temperature polishing agent grade and a practical evaluation plan.

在线留言

请填写有效的邮箱地址
验证码 不能为空

相关产品

chat

×

本网站使用 cookie 来确保您在我们的网站上获得最佳体验。

接受 拒绝